do not scale from this print tsm-1xx-xx-xxx-sv-xx-xxx-xx no of positions -02 thru -50 row specification -sv: single vertical (use tsm-xx-sv-xx) lead style see table 1 plating specification -t: tin (use t-1s6-xx-t-2) -s: selective (use t-1s6-xx-s-2) -g: gold (use t-1s6-xx-g-2) -l: light selective (use t-1s6-xx-l-2) -f: flash selective (use t-1s6-xx-f-2) -h: heavy gold (use t-1s6-xx-h-2) -p: gold flashed palladium nickel (use t-1s6-xx-p-2) -tl: tin / lead (use t-1s6-xx-tl-2) [lead style -01 & -02 only] -stl: selective tin / lead (use t-1s6-xx-stl-2) [lead style -01 & -02 only] -tm: matte tin -sm: selective heavy gold, matte tin on tail -lm: selective light gold, matte tin on tail -fm: flash selective gold , matte tin on tail option #3 -p: pick & place pad (see fig. 3) [use ppp-07](4 pos minimum or -02 & -03 pos with -tr) (see note 7) -tr: tape & reel (see note 7) (-02 thru -22 pos) option #1 -lc: locking clip (see fig. 1)(see note 8) [use lc-08-tm-02](-02 thru -36 pos: 2 per strip, -02 pos: 1 per strip) -a: alignment pin (see fig. 2) polarized position: specify pin omitted option #2 (no of pos x .100[2.54]) .100 ref 2.54 5 max sway (either direction) (no of pos -1) x .100[2.54] .000 .015 01 02 c3 tsm-xx-sv .025 sq ref 0.64 (typ) "b" .008[.20] (see table 1 & note 5) .010 ref 0.25 .099 2.51 .100 ref 2.54 (no of pos -2) x .100[2.54] 2 max sway (either direction) "f" (contact area) lc-08-tm-02 c1 t-1s6-xx-x-2 90 - 0 + 5 (typ) .050 .010 1.27 0.25 (typ) "d" max .056 ref 1.42 2 max toe (either direction) c2 c4 .006 "b" (see table 1 & note 5) "e" ref in-process .000 .005 c fig. 1 tsm-112-02-xxx-sv-lc shown sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: single row .100 smt assembly by: tsm-1xx-xx-xxx-sv-xx-xxx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 8/21/2002 2 1 sheet scale: 2.5:1 insulator: lcp, color: black terminal: phos bronze f:\dwg\misc\mktg\tsm-1xx-xx-xxx-sv-xx-xxx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. coplanarity to be within .006[.15]. 3. burr allowance: .0015[.038] max. 4. maximum cut flash: .015[.38] maximum on top & sides of body and .030[.76] maximum on surface mount side of body. 5. post height variation between any two pins: .005[.13] maximum. 6. maximum allowable bow: .002[.05] inch/inch after assembly. 7. leads may not be visible for customer visual inspectoin with -p option on smaller positions parts. 8. due to the high amount of insertion force needed, the Clc option is not compatible with auto placement. samtec recommends manual placement for all assemblies with the Clc option. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision bf
"c" .010[.25] .270 6.86 ref ppp-07 "a" = (no of positions x .100[2.54]) - .400[10.16] 2 .100 ref 2.54 (no of pos -2) x .100[2.54] ref -a: alignment pin option tsm-112-02-x-sv-a shown [different as shown, otherwise same as fig. 1] fig. 2 see table 2 * note: positions -02 thru -03 must be mold to position * .400 10.16 ref "a" .020 fig. 3 -p: pick & place pad option 4 position minimum [place pad on centerline as shown] c l .062 1.57 ref tube packaging fig. 4 notes: 1. load parts position 1 first in same direction as arrow. 2. note deleted 3. package positions -04 thru -36. fig. 5 -tr: tape & reel packagng option pos 1 (toward round hole) user direction of un-reeling pocket not detailed sheet of single row .100 smt assembly by: tsm-1xx-xx-xxx-sv-xx-xxx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 8/21/2002 2 2 sheet scale: 2:1 revision bf f:\dwg\misc\mktg\tsm-1xx-xx-xxx-sv-xx-xxx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
